Faber P147

P147 - 1 Litre

54.37 incl. VAT

Faber P147

In stock

P147 is a solvent-based, impregnating, color-enhancing, stain-proof, and wet-look non-filming treatment. It is used to enhance the colour and tone of absorbent surfaces, adding a matt finish without creating a surface film. P147 is recommended for treating natural stone, agglomerates, cotto and terracotta, and all materials with a medium-low, medium, and medium-high level of absorption.

Compared to traditional wet-look color enhancers, P147 penetrates deep into the materials without creating a surface film and it is extremely simple to apply without the risk of uneven aesthetic finishes. P147 thanks to these characteristics, is specifically indicated to be used outdoors or on surfaces that due to their nature, need to withstand conditions with the continued presence of water, such as showers, fountains, and washbasins. It has a lasting effect, can withstand UV rays and the elements, and will not yellow if exposed to sunlight.

Suitable for:

Agglomerate cement-marble

Agglomerate resin-marble



Basaltina - Lava Stone

Molted basalt

Cement tile






Manufactured Stone (Eco-stone)







The product is not suitable for use on polished surfaces.


✓ Strong color-enhancer
✓ Penetrates deep inside the material
✓ Leaves surface stainproof
✓ Provides water repellency
✓ Provides oil repellency
✓ Resistant to UV rays
✓ Will not yellow over time
✓ Adds a matt finish
✓ Will not create a film on the surface
✓ Also suitable for application outdoors.
✓ Certified safe for food contact


Brush, lambswool applicator, roller


Preparing and cleaning the surface

• Carefully clean the surface, making sure to remove any dust or dirt present.
• Never apply P147 to wet surfaces.
• Apply P147 to surfaces with a temperature of between +5 and +40°C
• Any adjacent surfaces not being treated with the product must be protected


• Apply an even, abundant coat of product to a clean, dry surface with the preferred tool, making sure to create an even layer to cover the whole surface being treated.
• About 5-10 minutes after application, and in any case, before the product is completely absorbed, as in cases of more absorbent surfaces, proceed to re-distribute the excess product using the same tool used for the application, taking care to achieve even coverage at the end of treatment.
• If the treatment is applied to the more absorbent material, where the product is absorbed without leaving residues, it is possible to apply a second coat of material, using the same methods, about 2-3 hours later.
• If the treatment has been applied to more compact and therefore, less absorbent materials, where the product is not completely absorbed, even following redistribution, and therefore, leaving surface residues, it is necessary to proceed to remove all residues thoroughly to prevent subsequent problems of grease. This operation is performed about 20-30 minutes after applying the product by brushing the surface, dry, using a standard floor polisher (1.5 HP, 175 rpm) with white or lambswool disc or wool-cotton attachment. Alternatively, on tops, upright surfaces, or small areas, residues can be removed with an orbital or manual wheel, using a white disc or pad, or a compact felt or wool-cotton cloth.
• To maximize the effectiveness of the stain-proofing treatment, the intensity of the color-enhancer, and the durability of the treatment, it is possible to wait over 20-30 minutes, up to a maximum of 45-60 minutes, before removing residues, to allow the product to penetrate fully and deep down inside the structure of more compact materials. This way, the surface residues may be slightly harder to remove.

Drying time

The product is fast drying and in any case, dries within 1-2 hours from application.

Opening to floor traffic

The surface can be opened to floor traffic about 4-6 hours after the product has been applied.


• For daily cleaning of a surface treated with P147, we recommend: NEUGEL or ALGAFLOOR
• For heavy-duty cleaning of a surface treated with P147, we recommend FABER 30 or DETERFUG, according to the type of material.
• For de-waxing a surface treated with P147, we recommend: DEC 21 and/or DECERA/P

Download Documents

What about these products?

Be the first to get tips, advice and special deals.
    Your cart is emptyReturn to Shop