Hidrofab AR

HIDROFAB AR 1 Litre

30.14 incl. VAT

Hidrofab AR

In stock

Purchase & earn 90 points!

HIDROFAB AR

HIDROFAB AR is a water-based wax-resin emulsion to use as a self-polishing, finishing treatment for floors in natural stone, cotto, concrete and porcelain stoneware, natural wood or parquet and textured ceramic tiles. The product seals the textured surface, creating a dirt-proof layer and making daily cleaning and maintenance operations on the floor much easier.

Treatment with HIDROFAB AR leaves the surface with a satin finish and it slightly enhances the original colour tone of the material. The protective layer created by HIDROFAB AR also stands out for its excellent water- and oil-repellent characteristics, to protect the surface against the formation of stains.

HIDROFAB AR is particularly recommended for use on natural stone with a distressed, brushed or fine sanded finish and can also be used for excellent results on concrete, cementina and cement agglomerates, cotto, terracotta and porous surfaces in general. Thanks to the special formula, the product can also be used on compact, non-absorbent surfaces with a textured surfaces, such as textured or micro rough porcelain stoneware.

 

Agglomerate cement-marble

Slate

Sandstone

Basaltina - Lava Stone

Cement tile

Concrete

Cotto

Granite

Porcelain gres Natural or Structured

Limestone

Marble

Quartzite

Terracotta

Travertine

If applied on high absorbent materials like cotto and terracotta, is better to pre-treat the surface with water-repellent products like AC 300 or DREP

 

HIDROFAB AR is a water-based wax-resin emulsion to be used as a self-polishing, finishing treatment for floors made of natural stone, Cotto, concrete, porcelain tiles, natural wood or parquet, and textured ceramic tiles.

The product seals the textured surface, creating a dirt-proof layer and making daily cleaning and maintenance operations on the floor much easier.

Treatment with HIDROFAB AR leaves the surface with a satin finish and it slightly enhances the original colour of the material. The protective layer created by HIDROFAB AR also stands out for its excellent water- and oil-repellent characteristics, protecting the surface against the formation of stains.

HIDROFAB AR is particularly recommended for use on natural stone with a brushed or fine sanded finish and can also be used for excellent results on concrete, concrete tiles, concrete agglomerates, Cotto, terracotta, and porous surfaces in general. Thanks to the special formula, the product can also be used on compact, non-absorbent surfaces with a textured surface, such as textured or micro rough porcelain stoneware.

CHARACTERISTICS AND BENEFITS OF HIDROFAB AR

✓ Satin-effect finish
✓ Effective protection against dirt and staining
✓ Gives the floor excellent water- and oil-repellency
✓ Excellent protection against foot traffic
✓ Won’t yellow overtime
✓ Applied quickly and easily
✓ Brings out the full aesthetic qualities of the treated surface

USES

The product is suitable for indoor use.

APPLICATION STEPS

Preparing and cleaning the surface

• Carefully clean the surface, making sure to remove any dust or dirt present.
• Never apply HIDROFAB AR to wet or damp surfaces.
• Apply HIDROFAB AR to surfaces with a temperature of between +5 and +40°C
• Any adjacent surfaces not being treated with the product must be protected.
When applying to medium-high-absorbency surfaces, we strongly recommend first applying a water-repellent product to act deep down and allow the HIDROFAB AR to catalyze correctly on the surface of the material.
When applying to compact, non-absorbent surfaces such as quartz, ceramic, or porcelain stoneware, dilute the product in water, to a ratio of 1:1.

Application

• Apply an even, abundant coat of product to a clean, dry surface with the preferred tool, making sure to create an even layer to cover the whole surface being treated. We recommend always following the same application direction. Take care not to leave too much product when applying wax and if you note any areas of product build-up, proceed to redistribute it while still working with the product in that specific surface area.
• If, while applying the wax, you should notice any build-up in an area where the product has already been applied, do not attempt to even out the layer of material: wait for the first layer to cure and then intervene to create a more even finish, as described in point
• In case of application on particularly absorbent or textured surfaces, it may be necessary to add a second coat of product. Only apply a second coat once the first is perfectly dry. Generally, 2-3 hours are sufficient between one coat and the next. Before applying a second coat, proceed in the same way as for the first. We recommend applying the second coat in a perpendicular direction to that of the first. This will create a “crisscross” application.

• HIDROFAB AR is a self-polishing wax that once applied, will create an extremely polished effect. In the event you wish to increase the surface shine, it is possible to do so using a traditional mechanical floor polisher with a white or lambswool pad. Wait a minimum of 3-4 hours for the wax to cure and then clean the surface dry, polishing until the required surface shine is achieved. Using a mechanical polisher also makes it possible to clean up any flaws created by a build-up of product in a specific surface area, in case of application of two coats of product.

Drying time

The product is fast drying and in any case, no more than 1-2 hours from application.

Opening to floor traffic

The surface can be opened to floor traffic about 4-6 hours after the product has been applied.

COMPLEMENTARY CLEANING AND MAINTENANCE PRODUCTS

For routine cleaning of a surface treated with HIDROFAB AR we recommend: NEUGEL or ALGAFLOOR.

For regular restoration of surfaces waxed with HIDROFAB AR, we recommend: MANU’ or even HIDROFAB AR diluted in water to a ratio of 1:5.

To dewax a surface treated with HIDROFAB AR we recommend: DEC 21 and/or DECERA P

INSTRUCTIONS AND GUIDELINES

• Never apply the product to wet, damp, or overheated surfaces.
• When applying to recently laid or grouted surfaces, wait for the adhesive or grout to cure completely.
• Do not use it on outdoor surfaces.
• Before applying the product to the whole surface, it is advisable to test a small, unexposed area or unused piece to check its suitability for use.

FABER YouTube

Download Documents

What about these products?

Be the first to get tips, advice and special deals.
0
    0
    Cart
    Your cart is emptyReturn to Shop